Pad Footing Calculator

What This Pad Footing Calculator Is For

This Pad Footing Calculator helps DIY builders, homeowners, and small contractors estimate concrete volume accurately for isolated pad footings.

It is designed for small residential and outdoor construction projects where precise concrete quantities, reinforcement planning, and material estimates matter — without using full structural engineering software.

This calculator is commonly used for:

• Concrete pad footing volume calculation
• Square and rectangular pad footings
• Individual footings under posts and columns
• Optional concrete pedestals
• Optional gravel subbase
• Reinforcement quantity estimates
• Ready-mix and concrete bag estimates
• Metric (mm) and imperial (in) units
• DIY and small construction projects

What Is a Pad Footing?

A pad footing (also called an isolated footing or pad foundation) is a single concrete foundation element used to support a concentrated load from a post, column, or structural member.

Pad footings are commonly used for:

• Pergolas and carports
• Deck and porch posts
• Sheds and small outbuildings
• Fences and gates
• Lightweight timber or steel structures

Unlike slabs or strip foundations, pad footings support loads at specific points only.

How to Calculate Concrete for Pad Footings

To calculate concrete volume correctly for pad footings, you need to know the footing dimensions, thickness, number of footings, and expected waste.

This calculator uses true geometric volume formulas instead of rough rules of thumb.

Required inputs include:

• Footing width
• Footing length
• Footing thickness
• Number of footings
• Waste percentage

Optional inputs include:

• Pedestal dimensions (width, length, height)
• Subbase (gravel) thickness
• Reinforcement configuration

All values can be adjusted, and results update instantly.

Square vs Rectangular Pad Footings

This calculator supports both common pad footing shapes.

Square pad footings are typically used when loads are symmetrical and space allows a uniform footing footprint.

Rectangular pad footings are used when:

• Loads are directional
• Space is limited
• Posts or columns are not centered
• Structural layouts require elongated foundations

The calculator automatically applies the correct volume formulas for each shape.

Pedestal Footings Explained

A pedestal is a raised concrete block cast on top of a pad footing.

Pedestals are commonly used to:

• Raise posts above ground level
• Improve durability and moisture protection
• Provide better connection points for columns or posts

If enabled, this calculator includes pedestal volume automatically in the total concrete calculation.

Subbase (Gravel) Under Pad Footings

A gravel subbase improves drainage and reduces frost-related movement.

Typical subbase thickness ranges from:

• 50–150 mm (2–6 inches)

If enabled, this calculator estimates subbase volume based on the footing footprint (width × length).

Reinforcement in Pad Footings

Reinforcement helps control cracking and improves footing durability, especially for larger or deeper footings.

Depending on the project, pad footings may include:

• Slab or footing reinforcement mesh
• Perimeter edge bars
• Vertical pedestal bars
• Ties (stirrups)
• Defined concrete cover

This calculator provides reinforcement quantity estimates to support material planning.
Final reinforcement design should always follow local building codes and structural requirements.

How Much Waste Should I Add?

A waste factor helps prevent running out of concrete due to uneven excavation, formwork leakage, or material loss during pouring.

Typical waste values:

• 0–5% – clean forms and very accurate excavation
• 5–10% – standard residential footing work
• 10–15% – uneven ground or complex formwork

You can set waste to 0% if you want an exact theoretical volume.

Common Mistakes When Estimating Concrete for Pad Footings

• Forgetting to include waste
• Mixing millimeters and inches
• Using unrealistic footing thickness
• Forgetting pedestal volume
• Ignoring subbase material
• Underestimating concrete bag quantities
• Ordering too little ready-mix concrete

Using a calculator helps avoid costly delays and re-orders.

Pad Footing vs Other Foundation Types

Pad footings are ideal for isolated loads and small structures.

Compared to other foundation types:

• Pad footings use less concrete than slabs
• They require less excavation
• They are faster to build for small projects

For full-area foundations, use a slab calculator instead.
For deep or drilled foundations, use a pile concrete calculator.

FAQ

How thick should a pad footing be?

Most residential pad footings are typically 150–300 mm (6–12 inches) thick, depending on load and soil conditions.

Do pad footings need reinforcement?

Reinforcement is recommended for larger footings, poor soil conditions, or when pedestals and tall posts are used.

Can I use this calculator for deck or pergola footings?

Yes. This calculator works well for deck posts, pergolas, carports, sheds, and similar small structures.

Is the cost estimate accurate?

No. The cost estimate is a rough approximation only.
Concrete prices vary by region, supplier, delivery distance, and order size.

Planning a Shed, Pergola, or Outdoor Structure?

CraftFrame plans include footing layouts, foundation dimensions, reinforcement guidance, and step-by-step instructions to help you build correctly and efficiently.

For pile foundations, use our Pile Concrete Calculator.
For slab-on-grade foundations, use our Concrete Slab Calculator.